Ezycoat
Paint

Enquire Now

Ezycoat
Paint

Enquire Now

Ezycoat
Paint

Enquire Now

Ezycoat Flexicote

Ezycoat Flexicote is revolutionary highly flexible yet durable exterior membrane paint finish for when you need that added protection against the elements. Its thickened appearance allows Ezycoat Flexicote to be applied either as a very thick coating or rolled out to suit your needs. Flexicote’s physical properties allow it to exhibit excellent crack bridging properties that are normally reserved to non-exposed elastomeric coatings.

Using the latest in European, technology it has been possible to develop a paint that has excellent adhesion, abrasive resistance and offers the ultimate in protection. The end result is a protective membrane coating that provides its user with a quality product, with ease of application.

Ezycoat Flexicote

Description: Ezycoat Flexicote is revolutionary highly flexible yet durable exterior membrane paint finish for when you need that added protection against the elements. Its thickened appearance allows Ezycoat Flexicote to be applied either as a very thick coating or rolled out to suit your needs. Flexicote’s physical properties allow it to exhibit excellent crack bridging properties that are normally reserved to non exposed water proofing coatings.

Surface Application: Suitable for application to Fibre cement sheeting, pre rendered surfaces, AFS, Ritek , Rendered Polystyrene Cladding, Koolwall Panel, Tilt Concrete & Modakboard* Refer to Technical Data Sheets (TDS). or Ezyspec for application procedures.

Mixing Procedure: Ready to use from the Pail.

Application Method: Ezycoat Flexicote is applied by either Brush or Roller. If spraying ensure a suitable tip is used.

Packaging: 15 Lit. Plastic Pails

Coverage: 50 to 60 sqm. per Pail. *Consumption will varying depending on surface to be coated

  • Use
  • Use

    Ezycoat Flexicote

    Contact Us

    1300566592

    Ezycoat Flexicote is a specially designed decorative pigmented protective coating system for application over such products as Ezycoat Skim Render, Ezycoat ECA, Super 6, Conventional Render and various other Ezycoat texture finishes. It is also suitable for application over non porous & porous concrete substrates such as precast concrete & concrete block.

    The final product will produce a protective membrane which exhibits excellent durability and high water and U.V. resistant and flexibility. Its extra thick film forming ability and properties still enable Ezycoat Flexicote to maintain excellent transpiration properties while still exhibiting water resistance to the external surface.

  • Application
  • Application

    Ezycoat Flexicote Mixing Procedures

    Contact Us

    1300566592

    Prior to application of Ezycoat Flexicote to a surface it is essential that the surface be free of any contaminants that may affect the performance of the paint system. The sequence of coating application will vary depending on the surface to which the Ezycoat Flexicote is to be applied. Table 1 provides application procedures for various surfaces and estimated product usage. It is essential that the trade contractor applying the product makes a suitable inspection of the intended applicating surface prior to commencing works. If in doubt please contact our offices for further advice.

    Ezycoat Flexicote is ready to use, out of the pail and does not require the addition of any extra water. Ezycoat Flexicote is applied by a min 24mm Long Nap Roller. This will assist with minimum film build being achieved. However the applicator will need to implement a structured supervisory plan should specific film build be specified. The responsibility of Dry film thickness (DFT) required & achieved on a project will be left with the applicator. Should any doubt exist in achieving the specified dry film thickness, then the applicator should contact our offices immediately before proceeding with any further with the application.

    Ezycoat Flexicote Application Specification Sequence.*

    Estimated Product Usage Sqm/Lit Coating Sequence Render,Ezycoat SkimRender, Pump Render Super 6 etc. Textured Finishes Fine Finish Sandstone Polymer etc.
    3 1 1 st Coat Ezycoat Masonry Sealer 1 st Coat Ezycoat Flexicote
    3 2 2 nd Coat Ezycoat Flexicote 2 nd Coat Final Coat Ezycoat Flexicote
      3 3rd Coat Final Coat Ezycoat Flexicote  

    * With some darker colours it may be necessary to apply an additional coat of Ezycoat Flexicote in order to maintain DFT. This will be at the discretion of the Painting Contractor to determine or if in doubt contact our offices for further advice.

    Ezycoat Flexicote 1 st. Coat & 2nd Coat should be allowed to dry for a min. of 8 Hrs. prior to proceeding with the Final coat. The finishing coat will require a minimum of 12 Hrs. to dry in full. This may vary depending on whether conditions. It is recommended that the process of cutting in, be carried out at the same time as rolling the Ezycoat Flexicote on the walls so as to maintain a wet on wet application. This will reduce the effect of roller marks on the wall. Always try to apply Ezycoat Flexicote in shaded areas out of the direct sun. Should rain forecasted or seen as being a problem within 48 hrs. of applying the Flexicote paint it is highly recommended that the application of the Ezycoat Flexicote be postponed until such time as rain has cleared. Substrates must contain less than 15% Wood-MoistureEquivalent before painting.

    Consumption

    Ezycoat Flexicote white base

    Product Consumption for Rendered wall

    0.20 Lit./ sqm. per coat

    Product Coverage on a Textured Surface

    (will vary for different textures)

    0.30 Lit./ sqm. Per coat.
    Application Min 24mm Nap Roller or Brush
    Base Water
    Drying Time Between 8 to 12 Hours
    Colour Various Bases. Available to tint to your needs.
    Classification Non Dangerous/ Non Flammable

    Technical Data

    Density 1.43 kg/ Lit. Volume Solids:- 52%
    Recommended film thickness per coat 200 micron (wet) 100 microns. (DFT)
    Moisture Control Excellent (Surface must not be exposed to hydrostatic pressures)
    Physical Appearance Thick, Creamy Paste
    Elongation 600%
    Excellent Abrasion Resistance  
    Clean up Water when wet. Dry product should be removed with a weak solvent.
  • Technical Spec
  • Technical Spec

    Ezycoat Flexicote

    Contact Us

    1300566592

    Ezycoat Flexicote should not be applied at temperatures below 7 degrees Celsius or when there is the possibility of rain. The durability of the product in its original confection is guaranteed for 1 year as long as it is not exposed to direct sunlight or temperatures below 4 degrees or had the addition of any other products such as water.
     
    Ezycoat Flexicote is not suitable for use in areas prone to water logging, submersion, continually damp and/or below ground. Walls were Ezycoat Flexicote is to be applied must be free draining. In the case of retaining walls the rear of the wall must be engineered to prevent any penetration of moisture or water through the wall in to the rear of the Ezycoat Flexicote. Failure to do so will result in damage to the Ezycoat Flexicote and is not covered by warranty.

    Ezycoat Flexicote is to be applied only by trade’s persons holding a license for this trade as recognised by the legislative building authority for the relevant state to which the work is being carried out. Misuse of this product and/or noncompliance with technical specifications will void any warranties weather verbal or written.

    Active Building Systems Pty Ltd reserves the right to change, update and republish these specifications without any notice. It is the user’s responsibility to attain the most current publication of Ezycoat Specifications from Active Building Systems Pty Ltd. at the time of the project.

  • Data Sheet
  • Data Sheet

    Ezycoat Flexicote

    Contact Us

    1300566592

    Consumption

    Ezycoat Membrane white base

    Product Consumption for Rendered wall

    0.20 Lit./ sqm. per coat

    Product Coverage on a Textured Surface

    (will vary for different textures)

    0.30 Lit./ sqm. Per coat.
    Application Long Nap Roller or Brush
    Base Water
    Drying Time Between 8 to 12 Hours
    Colour

    Various Bases

    Available to tint to your needs.

    Classification Non Dangerous/ Non Flammable

    Technical Data

    Density

    1.43 kg/ Lit. Volume Solids:- 52%

    Recommended Film Thickness per coat

    200 micron (wet) 100 microns. (DFT)
    Moisture Control Excellent (Surface must not be exposed to hydrostatic pressures)
    Physical Appearance Thick, Creamy Paste
    Elongation 600%
    Excellent Abrasion Resistance  
    Clean up Water when wet. Dry product should be removed with a weak solvent.
  • Downloads
  • Downloads

    Ezycoat Flexicote Downloads

    Contact Us

    1300566592

    Gallery

    Click here to find out how our
    products can benefit your next job